I will say the job was delayed three days in starting because of rain, not your fault. And after that the crews came and worked very, very diligently for many days until the job was done. Overall I think it was a great job, the roof looks great, the gutters look great and I'm very satisfied with it.
Metal Roofing · City of South Miami · ZIP 33143, 33155
Metal roofing in South Miami.
Standing-seam aluminum on contemporary remodels and UM-corridor modern builds, 16-oz copper accents on Mediterranean revival rebuilds. Filed under the City of South Miami.
Schedule Your South Miami Metal Consultation →Since 1985
Family-owned
What makes metal roofing the right choice for South Miami homes?
Metal is the right call on contemporary South Miami remodels and UM-corridor modern builds where the architecture asks for a generational standing-seam surface. 16-oz copper accents are the right move on Mediterranean revival rebuilds for porches, dormers, and bay windows. Aluminum lasts 50+ years in South Miami exposure, with moderate salt-air load (1–2 miles inland of Biscayne Bay, not direct-coastal) to spec around.
Why metal in South Miami
The contemporary spec, at city scale.
South Miami metal work serves two main contexts. Contemporary remodels and modern infill builds across the city carry standing-seam aluminum as the primary roof. Mediterranean revival rebuilds (mostly along the UM corridor) use 16-oz copper as architectural accent at porches, dormers, and prominent entry features rather than as the main-house material.
The dominant spec is aluminum in PVDF Kynar matte finish. The panel runs 50-plus years in this near-coastal exposure (moderate salt-air load 1–2 miles inland of Biscayne Bay, not direct-ocean), and the matte finish holds color across decades without chalking.
Copper accents on Mediterranean revival rebuilds are hand-formed in our shop and installed as architectural detail rather than field roof. The visible result reads as intentional craft against the surrounding tile or stucco.
Galvalume rounds out the roster on contemporary South Miami builds. The aluminum-zinc alloy coating over a steel substrate runs more rigid than aluminum and holds a Kynar 500 or Sheffield COOLR finish, backed by the McElroy Galvalume substrate warranty. We spec it where a steel substrate and a modern silhouette suit the remodel.
What stays consistent across panels is the installation discipline. Polyglass SA-V peel-and-stick underlayment with a current Miami-Dade NOA, mechanical clip attachment continuous across every elevation, and hand-formed trim at every flashing detail.
South Miami Metal Specifications What gets installed,
What gets installed,
and why.
The six numbers and credentials that define a South Miami metal install. Verified against current NOA filings and manufacturer documentation.
Material
Aluminum (Kynar), 16-oz copper, galvalume
Aluminum in PVDF Kynar finish carries most South Miami metal volume. 16-oz copper on prominent accent features: porches, dormers, and bay windows on Mediterranean revival rebuilds. Galvalume, an aluminum-zinc alloy over steel, suits contemporary UM-corridor builds under the McElroy substrate warranty.
Profile width
12 to 18 inch standing-seam
Wider panels read contemporary on modern remodels and UM-corridor new builds. Tighter rib spacing suits transitional homes and Mediterranean revival accent runs.
Lifespan
50+ years
Aluminum and copper exceed 50 years in inland South Miami service. The mature city canopy is friendly to metal: less debris retention than tile, and moderate salt-air load 1–2 miles inland of Biscayne Bay rather than direct-coastal exposure.
Wind rating
200+ mph uplift on certified standing-seam
Mechanically seamed standing-seam panels with continuous clip attachment exceed Miami-Dade HVHZ's 175 mph minimum. Filed under current NOA documentation across every City permit.
Finish
PVDF Kynar 500 matte
Matte finishes in muted earth tones (weathered copper, warm bronze) read consistent with South Miami's mature canopy context. PVDF Kynar holds color across decades without chalking.
Investment
Scoped by material and profile
Aluminum anchors the lower end of the range; 16-oz copper accents on Mediterranean revival features sit higher, justified on architecturally prominent properties. Most full metal projects land within our $25,000 to $80,000 roof-replacement range.
What's Different About South Miami Metal The four things only the city
The four things only the city
asks of metal.
Local note 1
Contemporary remodels
South Miami's contemporary remodels and modern infill builds increasingly choose standing-seam aluminum. Wider rib profiles, matte Kynar finishes, and clean continuous runs read as the right material for the architectural register.
Local note 2
UM-corridor architecture
The streets immediately around the University of Miami carry a mix of Mediterranean revival inventory and contemporary new construction. Metal serves the contemporary block; tile serves the Mediterranean. The material follows the home.
Local note 3
Accent applications on rebuilds
On Mediterranean revival rebuilds, 16-oz copper accents at porches, dormers, and bay windows add architectural craft without replacing the main-house tile. We hand-form the trim and coordinate the transition to surrounding tile or stucco.
Local note 4
City of South Miami permitting
South Miami operates its own Building Department, separate from Coral Gables, Pinecrest, and unincorporated Miami-Dade. We file directly with the City. NOA letters and HVHZ wind specs are identical to county code.
Permitting and City Code
Filed under City code, built to HVHZ.
Every South Miami metal install carries the standard Miami-Dade HVHZ wind permit from the City of South Miami Building Department, with the current Notice of Acceptance on the panel system, the clip attachment pattern, and the underlayment. The City adopts HVHZ without modification.
Some 33155 ZIP addresses fall under the adjacent City of Coral Gables jurisdiction and route through Board of Architects review on visible exterior changes. We confirm jurisdiction at the consultation and file with the correct authority.
External references for verification:
- City of South Miami Building Department: permit, inspection, and code reference.
- Miami-Dade County Product Approval (NOA) Search, for verifying the active NOA on any product specified.
- Petersen Aluminum (PAC-CLAD): standing-seam panel and PVDF Kynar finish documentation.
From the City
South Miami metal owner.
Frequently Asked
South Miami metal, answered.
A defensible specification and the right material for many South Miami contemporary remodels. Aluminum standing-seam in PVDF Kynar finish carries the 50-plus year service life, the HVHZ wind rating, and a clean profile that reads contemporary against the city's mature canopy. We bring panel samples to the consultation to confirm the right finish for the architectural register.
16-oz copper at porches, dormers, bay windows, and entry porches reads as architecturally appropriate craft on Mediterranean revival rebuilds. We hand-form the trim, coordinate the transition to surrounding tile or stucco, and design the accent runs so they look intentional rather than tacked on. Most South Miami copper accent installs we file approve on first review.
The canopy is friendly to metal. Aluminum and copper standing-seam panels shed leaf and seasonal debris naturally, biological growth that affects tile in shaded areas is essentially absent on metal, and South Miami's position 1–2 miles inland of Biscayne Bay (moderate salt-air load rather than direct-coastal) means aluminum finish life runs to the higher end of its rated window.
PVDF Kynar 500 in muted earth tones reads correctly against the city's tree-lined streetscape and stucco-and-tile context. Weathered copper, warm bronze, soft terracotta, and matte black on accent runs are the typical specifications. We bring sample panels to the consultation so the decision is made against the actual surroundings.
A standard metal permit through the City of South Miami Building Department runs five to ten business days for non-historic-district homes. The City does not maintain a separate architectural review layer, so the cycle is generally shorter than Coral Gables historic district work. We confirm jurisdiction (City of South Miami vs. City of Coral Gables for some 33155 addresses) at the consultation.
Sometimes, depending on the architectural register. A contemporary remodel of a mid-century home can wear standing-seam metal correctly. A pure mid-century ranch in original architectural condition typically wears architectural shingle instead. We make the call at the consultation based on the architecture and the homeowner's intent for the remodel.
A standing-seam metal roof in South Miami requires almost no scheduled maintenance through its service life. An annual visual inspection of flashings and fastener heads, plus a soft-wash cleaning every five to seven years to remove canopy debris and biological dust. That is the entire cadence.
A South Miami metal roof,
filed under the City.
We will be on your roof within ten business days. Bring us the elevation photos and the architectural register of the remodel. We will handle the permit, the finish approval, and the work.
Or call us directly at (305) 671-9190